Suitable for
Projects that match this page decision
- Projects targeting about 5,000 saleable 500 ml bottles per hour
- PET still-water projects preparing a controlled machine requirement
- Buyers able to confirm bottle, cap, output basis and destination
High-intent buyer search / machine-specific planning
5,000 BPH Bottled Water Filling Machine Selection
A 5,000 BPH sales target should be converted into a machine requirement with downtime, changeover and growth reserve. The nearest published Allot Tech XGF reference is 6,000 BPH on a 500 ml basis, subject to project confirmation.
Answer first
For a project that must reliably sell 5,000 good 500 ml bottles each hour, a nominal 5,000 BPH machine may leave no operating reserve. Review the published 6,000 BPH XGF14-12-5 band, then confirm actual bottle behavior, net efficiency, cap handling and downstream balance before selection.
Not suitable for
Boundaries that need a different platform or review
- Assuming a 5,000 BPH keyword automatically identifies one exact machine model
- Carbonated, hot-fill, glass, can or returnable 5-gallon platforms
- Treating a search phrase or nominal BPH as a final machine guarantee
Inputs required
Evidence to provide before confirmation
- Required good bottles per hour plus planned operating efficiency and changeover loss
- Approved bottle drawing, neck finish, cap drawing and representative samples
- Saleable daily demand, net production hours, efficiency basis and destination
Machine function
What happens at this machine or decision boundary
- The preliminary review compares the 5,000 BPH demand with the 6,000 BPH published reference band.
- The rinse-fill-cap platform is reviewed against the approved PET container and still-water process.
- Project engineering confirms the model, components, interfaces and acceptance basis.
Configuration decisions
Options that must appear in the proposal
- Whether the capacity reserve is adequate for stops, ramp-up and future demand
- Machine-only, machine-plus-interface or complete-line commercial boundary
- Change parts, controls, documents, spares, FAT and service responsibility
Interface requirements
Upstream, downstream and utility handovers
- Infeed and downstream equipment must sustain the required good-bottle rate.
- Treated product-water, electrical, controls and drainage handovers
- Filled-bottle discharge, downstream accumulation, labeling and packing route
Buyer risks
Questions to close before order
- Buying a nominal 5,000 BPH platform with no recoverable output reserve
- Comparing supplier proposals built on different container or efficiency assumptions
- Leaving exclusions, utilities, installation or acceptance evidence unstated
FAT checks
How to verify the agreed basis
- Verify the agreed saleable-output basis rather than counting short peak speed.
- Run approved production-representative bottles and caps under a written test method.
- Record output, stops, transfer, fill level, leakage, capping, alarms and open points.
Quotation scope
What the commercial offer should state
- State 5,000 saleable BPH as the requirement and identify the proposed reference model.
- Reference output basis, included interfaces, change parts, spares and documents
- FAT, packing, freight, installation, commissioning, exclusions and confirmation items
Search questions / buyer answers
Questions buyers ask before requesting a quotation
What information is required before confirming 5,000 BPH Bottled Water Filling Machine Selection?
Required good bottles per hour plus planned operating efficiency and changeover loss. Approved bottle drawing, neck finish, cap drawing and representative samples. Saleable daily demand, net production hours, efficiency basis and destination.
What should the quotation state for 5,000 BPH Bottled Water Filling Machine Selection?
State 5,000 saleable BPH as the requirement and identify the proposed reference model. Reference output basis, included interfaces, change parts, spares and documents. FAT, packing, freight, installation, commissioning, exclusions and confirmation items.
How should 5,000 BPH Bottled Water Filling Machine Selection be checked during FAT?
Verify the agreed saleable-output basis rather than counting short peak speed. Run approved production-representative bottles and caps under a written test method. Record output, stops, transfer, fill level, leakage, capping, alarms and open points.
Related decision
Selection Tools
Calculate preliminary required BPH from daily saleable bottles, net hours, planning efficiency and growth reserve, then compare an XGF reference band.
Allot Tech / 5000-bph-bottled-water-filling-machine-selection
Turn this decision into a comparable machine scope
Send the bottle, cap, reference output, existing equipment and destination. Final values are confirmed in the project proposal.