High-intent buyer search / machine-specific planning

10,000 BPH Bottled Water Filling Machine Selection

A 10,000 BPH requirement sits between the published 8,000 and 13,000 BPH XGF references on a 500 ml basis. Selection must distinguish target saleable output from catalog nameplate output.

Plan My 10,000 BPH Machine WhatsApp +86 186 6213 1120

Allot Tech 2026 catalog imageReference values require project-specific confirmation.

Answer first

Do not select the 8,000 BPH reference for a confirmed 10,000 good-bottle requirement. The 13,000 BPH XGF24-24-8 band is the logical preliminary comparison, but the final model still depends on bottle size, efficiency, cap, interfaces and the written FAT method.

Suitable for

Projects that match this page decision

Automatic PET water projects targeting approximately 10,000 saleable bottles per hour
PET still-water projects preparing a controlled machine requirement
Buyers able to confirm bottle, cap, output basis and destination

Not suitable for

Boundaries that need a different platform or review

Using the 8,000 BPH published reference for a 10,000 BPH contractual requirement
Carbonated, hot-fill, glass, can or returnable 5-gallon platforms
Treating a search phrase or nominal BPH as a final machine guarantee

Inputs required

Evidence to provide before confirmation

Hourly demand, bottle-size mix, net operating hours and required recovery margin
Approved bottle drawing, neck finish, cap drawing and representative samples
Saleable daily demand, net production hours, efficiency basis and destination

Machine function

What happens at this machine or decision boundary

The selection review brackets 10,000 BPH between published XGF capacity bands.
The rinse-fill-cap platform is reviewed against the approved PET container and still-water process.
Project engineering confirms the model, components, interfaces and acceptance basis.

Configuration decisions

Options that must appear in the proposal

Whether the 13,000 BPH reference provides the right project reserve without oversizing downstream equipment
Machine-only, machine-plus-interface or complete-line commercial boundary
Change parts, controls, documents, spares, FAT and service responsibility

Interface requirements

Upstream, downstream and utility handovers

Air conveyor, outfeed, labeler and packer must be balanced for the confirmed line rate.
Treated product-water, electrical, controls and drainage handovers
Filled-bottle discharge, downstream accumulation, labeling and packing route

Buyer risks

Questions to close before order

Comparing a 10,000 BPH sales need with an 8,000 BPH catalog reference
Comparing supplier proposals built on different container or efficiency assumptions
Leaving exclusions, utilities, installation or acceptance evidence unstated

FAT checks

How to verify the agreed basis

Measure sustained good bottles over the agreed run period with downstream conditions recorded.
Run approved production-representative bottles and caps under a written test method.
Record output, stops, transfer, fill level, leakage, capping, alarms and open points.

Quotation scope

What the commercial offer should state

Show the proposed model, 500 ml rating basis and guaranteed project-specific output separately.
Reference output basis, included interfaces, change parts, spares and documents
FAT, packing, freight, installation, commissioning, exclusions and confirmation items

Search questions / buyer answers

Questions buyers ask before requesting a quotation

What information is required before confirming 10,000 BPH Bottled Water Filling Machine Selection?

Hourly demand, bottle-size mix, net operating hours and required recovery margin. Approved bottle drawing, neck finish, cap drawing and representative samples. Saleable daily demand, net production hours, efficiency basis and destination.

What should the quotation state for 10,000 BPH Bottled Water Filling Machine Selection?

Show the proposed model, 500 ml rating basis and guaranteed project-specific output separately. Reference output basis, included interfaces, change parts, spares and documents. FAT, packing, freight, installation, commissioning, exclusions and confirmation items.

How should 10,000 BPH Bottled Water Filling Machine Selection be checked during FAT?

Measure sustained good bottles over the agreed run period with downstream conditions recorded. Run approved production-representative bottles and caps under a written test method. Record output, stops, transfer, fill level, leakage, capping, alarms and open points.

Related decision

Selection Tools

Calculate preliminary required BPH from daily saleable bottles, net hours, planning efficiency and growth reserve, then compare an XGF reference band.

Allot Tech / 10000-bph-bottled-water-filling-machine-selection

Turn this decision into a comparable machine scope

Send the bottle, cap, reference output, existing equipment and destination. Final values are confirmed in the project proposal.